Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Alumina ceramics with different unit numbers and gradient modes were prepared by digital light processing (DLP) 3D printing technology. The side length of each functional gradient structure was 10 mm, the porosity ratio was controlled to 70%, and the number of units were (1 × 1 × 1 unit) and (2 × 2 × 2 unit) respectively. The different gradient modes were named FCC, GFCC-1, GFCC-2 and GFCC-3. SEM, XRD, and other characterization methods proved that these gradient structures of alumina ceramics had only α-Al2O3 phase and good surface morphology. The mechanical properties and energy absorption properties of alumina ceramics with different functional gradient structures were studied by compression test. The results show that the gradient structure with 1 × 1 × 1 unit has better mechanical properties and energy absorption properties when the number of units is different. When the number of units is the same, GFCC-2 and GFCC-3 gradient structures have better compressive performance and energy absorption potential than FCC structures. The GFCC-2 gradient structure with 1 × 1 × 1 unit has a maximum compressive strength of 19.62 MPa and a maximum energy absorption value of 2.72 × 105 J/m3. The good performance of such functional gradient structures can provide new ideas for the design of lightweight and compressive energy absorption structures in the future.     

SLM printing of cermet powders: Inhomogeneity from atomic scale to microstructure

It is very challenging for 3D printing based on the selective laser melting (SLM) technology to obtain cermet bulk materials with high density and homogeneous microstructures. In this work, the SLM process of the cermet powders was studied by both simulations and experiments using the WC-Co cemented carbides as an example. The results indicated that the evolution of the ceramic and metallic phases in the cermet particle during the heating, melting and solidification processes were all significantly inhomogeneous from atomic scale to mesoscale microstructures. As a consequence, the microstructural defects were caused intrinsically in the printed bulk material. The formation and growth of the bonding necks between the particles were mainly completed at the later stage of laser heating and the early stage of solidification. Both simulations and experiments demonstrated that thin amorphous layers formed at the ceramics/metal interfaces. This work disclosed the mechanisms for the evolution from the atomic scale to microstructure during the SLM printing of cermet powders, and discovered the origin of the defects in the printed cermet bulk materials.     

Grain orientation evolution and multi-scale interfaces enhanced thermoelectric properties of textured Sr0.9La0.1TiO3 based ceramics

Sr_0.9La_0.1TiO₃ based textured ceramics (SLTT-S3T) with a texture fraction of 0.81 are successfully fabricated by the reactive template grain growth method, in which Sr_0.9La_0.1TiO₃/20 wt%Ti was used as matrix and 10 wt% plate-like Sr₃Ti₂O₇ template seeds were used as templates. The phase transition, microstructure evolution, and the anisotropic thermoelectric properties of SLTT-S3T ceramics were investigated. The results show that the ceramics are mainly composed of Sr_0.9La_0.1TiO₃ and rutile TiO₂ phases. Grains grow with a preferred orientation along (h00). A maximum ZT of 0.26 at 1073 K was achieved in the direction perpendicular to the tape casting direction. The low lattice thermal conductivity of 1.9 W/(m K) at 1073 K was obtained decreased by 34%, 40%, and 38% compared with non-textured, SrTiO₃ and Sr_0.9La_0.1TiO₃ ceramics prepared by the same process, can be attributed to the enhanced phonon scattering by the complex multi-scale boundaries and interfaces. This work provides a strategy of microstructural design for thermoelectric oxides to decrease intrinsic lattice thermal conductivity and further regulate thermoelectric properties via texture engineering.     

Development of silica based organic slurries for stereolithographic printing process

In this study, silica based slurries for stereolithographic printing of glass structures are developed and characterized. Stereolithography has the potential to print complex structures with high resolution. Therefore, acrylate based photocurable slurries have been developed and their viscosities are examined as a function of the solid loading. A critical shear rate can be derived, which must not be exceeded during the printing process. Therefore, rheological characterizations provide important insights into the printing process and the ability to produce samples with precise structures. Other properties such as polymerization time and curability kinetic were investigated with time dependent attenuated total reflection infrared spectroscopy (ATR-IR). Afterwards, the slurries were printed on a commercial printer operating with visible light. For debinding the printed green bodies, the decomposition temperatures were derived from thermogravimetric analysis in order to obtain stable and transparent samples.     

A review of the existing performance verification infrastructure for micro-CMMs

The performance verification of micro-CMMs is now of intense interest because of their capability to perform length measurements in three dimensions to high accuracy with low uncertainties. Currently, verification of micro-CMMs is completed in the spirit of existing specification standards, because strict adherence to these standards is often difficult. This review aims to present and discuss verification techniques available for micro-CMMs: specification standards, existing calibrated test lengths and traceability routes that can be associated with micro-CMMs. Three specification standards used in the testing of CMMs will be considered. In addition, a wide range of calibrated test lengths are reported, and any advantages and disadvantages associated with their use are discussed. It is concluded that micro-CMMs cannot yet be verified in accordance with existing specification standards. Suggestions are made for future standardisation work required to rectify these issues.     

On the modeling of bending responses of graphene-reinforced higher order annular plate via two-dimensional continuum mechanics approach

This research presents bending responses of FG-GPLRC plates based upon higher order shear deformation theory (HSDT) for various sets of boundary conditions. The rule of the mixture and modified Halpin–Tsai model are engaged to provide the effective material constant of the composite layers. By employing Hamilton’s principle, the governing equations of the structure are derived and solved with the aid of the differential quadrature method (DQM). Afterward, a parametric study is done to present the effects of three kinds of FG patterns, weight fraction of the GPLs, radius ratio, and thickness to inner radius ratio on the bending characteristics of the FG-GPLRC disk. Numerical results reveal that in the initial value of the \(Zt/h\), using more GPLs for reinforcing the structure provides an increase in the normal stresses but this matter is inverse for the higher value of the \(Zt/h\). The results show that considering the smaller radius ratio is a reason for boosting the shear stresses of the structure for each \(Zt/h\). Another consequence is that for the negative value of \(Zt/h\), it is true that by increasing \(h/{R}_{i}\) , the normal stresses increases but if there is positive value for \(Zt/h\), the radial and circumferential stresses fall down by having an increase in the \(h/{R}_{i}\).

     

SBBR反应器中耐冷微生物的驯化与识别

以模拟生活污水为处理对象，三种不同填料为生物膜载体，运行 A、B、C三个SBBR，通过逐步降温（25、20、15、10、6和5℃）培养驯化处理低温污水的生物膜。运行251周期，三个反应器COD出水浓度均低于50 mg/L；B反应器对氨氮去除效果优于A和C。特别在低温5℃时，A、B和C三个反应器氨氮平均出水浓度分别为14.1、3.79和14.1 mg/L。高通量测序结果显示，5℃时，三个反应器中均以降解有机物的微生物为主；只有B反应器中驯化富集出了嗜冷硝化菌（Candidatus Nitrotoga）；而其他有硝化作用的菌属在B反应器中的丰度也高于A和C反应器；不利于脱氮的类固氮菌（Elstera）在A和C反应器中丰度较高。此结果可从微生物角度解释三个反应器处理效果的差异性，表明B反应器处理低温污水有显著优势，其所用填料可结合低温菌进一步开发利用。     

A zirconium-free glaze system for sanitary ceramics with SiO2-CaCO3-TiO2 composite opacifier containing anatase: Effect of interface combination among SiO2, CaCO3 and TiO2

TiO₂ is an ideal substitute to ZrSiO₄ ceramic opacifier, yet it is limited to application because of the undesirable yellowing resulting from rutile formation. Herein, the SiO₂-CaCO₃-TiO₂ composite opacifier (Si-Ca-Ti) was constructed. The glaze used Si-Ca-Ti presents a superior opacification performance than ZrSiO₄ opacified glaze without causing yellowing, showing L*, a*, b* values of 94.81, -0.67 and 3.23. By comparison, the glaze using SiO₂, CaCO₃, and TiO₂ mixture shows lower opacification and yellowish surface with L* and b* values of 92.99 and 5.36. It is revealed that there is a close interface bonding among SiO₂, CaCO₃ and TiO₂ in Si-Ca-Ti, which promotes their combination reaction to generate opacification phase titanite and inhibit rutile formation when sintering, resulting in the white surface and opacification improvement of the glaze. This study proposes a green and efficient strategy to achieve white and highly opacified glaze for sanitary ceramics, exhibiting good application prospect.     

Numerical integration for the inverse dynamics of a large class of cranes

Multibody System Dynamics - A recently developed index reduction method is applied to comparatively complicated underactuated mechanical systems in the context of inverse dynamics. The inverse...